Nowadays, there is a huge amount of building materials. Polyurethane foam is considered one such material. Construction experts will agree that polyurethane foam is very often used in construction and renovation, and sometimes it is simply not replaceable. Foam is a polyurethane foam sealant. It is made from oil refining waste.
It is worth noting that the process of foam getting on the surface of clothing is very undesirable. Because this type of contamination is very difficult to remove from fabrics. Simple detergents are powerless in this matter. But this is not a reason to despair and begin a difficult farewell to your favorite pants or jacket, since there are other specific ways to remove stains of similar origin. It is worth noting that in case of contamination, it is necessary to begin removing stains as quickly as possible, since in a short period of time the foam will not have time to settle deeply and firmly into the structure of the fabric.
Methods for quickly removing polyurethane foam from clothes
In the case when the fact of foam contamination is noticed, the stain can be immediately removed using a homemade product. It's not cool to do this salt solution in warm water. The desired area is rubbed with this solution or washed in it, and then you just need to rinse the item.
Fresh contamination is also removed strong soap solution, but before that it needs to be warmed up a little. It heats up to such an extent that you can work with this solution painlessly.After removing the stain, the product must be rinsed.
When the stain is not noticed in time and the foam has had time to be strongly absorbed into the fabric, it will help solar heat. It is necessary to place the product in a place where there is constant direct sunlight. Under the influence of sunlight, the structure of the foam changes and it can be separated from the fabric much more easily.
If the amount of foam that gets on the fabric is large enough, it is recommended to remove the protruding part. To do this you will need a very sharp device. This could be a knife, blade, or a nail file from a manicure set. The process of removing foam should be as careful as possible, since you should be wary of damaging the fabric. The amount of foam that is deeply ingrained into the fabric can be removed using special aerosols. Aerosol cleaners are commercially available. You can find them in hardware or hardware stores. Having purchased such a product, you should pay attention to the instructions. Do not use an aerosol that states that it may cause tissue damage. It is necessary to purchase products that are safe for clothing, otherwise the fabric may be damaged and such a damaged item can only be thrown in the trash. If the instructions do not mention the risk of using a clothing product, it is worth doing a small test. To do this, spray a little aerosol onto a hidden area of the item and leave it for a couple of minutes. If no visible damage has occurred within the expected period of time, then you can begin the process of removing foam contaminants.
Before you start the process of spraying the aerosol, you must first shake the can itself well.This must be done within 5 seconds. After this, the product is applied directly to the site of contamination. Spraying is carried out in such a way that the aerosol falls on the stain itself, and not on the clean fabric. After treating the contaminated area, leave the item for 25 minutes. After the specified time, the remaining foam is removed using a damp cloth or regular sponge. After this, proceed to complete cleansing. Clean warm water is filled into the container, in which the item is thoroughly rinsed. After this, it is necessary to carry out a full wash with the addition of liquid or dry powder.
In the event that a one-time treatment does not give the most positive results, the cleaning procedure should be repeated. This involves repeating the previous process step by step.
Of course, it is not always possible to use an aerosol, so it can be replaced white - pyrite or gasoline, and it is better to choose purified. It is worth noting that the above substitutes are less effective, but they do not injure the fabric of the product as much.
In order to remove this complex stain, it is necessary to soak the stained area in one of these products for 15 minutes. During this period of time, the polyurethane foam will be able to dissolve. After this, it is recommended to carry out mandatory washing and rinsing. When washing, add a small amount of standard stain remover to the water.
Polyurethane foam is characterized by good stain removal properties. turpentine. It, like other similar solvents, is applied with a cotton swab or swab to the desired location and left for 20 minutes.After this, it is removed with a napkin and then rinsed thoroughly with warm running water.
It is effective in combating pollution cold. To do this, you will need to put the soiled item in a regular bag and place it in the freezer. The product should lie there for 2 or even better 3 hours. After the holding time has expired, the package is taken out. You should try to remove any remaining foam using any sharp object. This should happen very easily. Of course, there is a high probability that you will not be able to completely get rid of the stain, so you need to take a cotton swab and soak it in acetone or nail polish remover. Then use this swab to wipe the area of contamination. After this procedure, it is also recommended to thoroughly wash the product using powder and stain remover.
It may seem strange, but you can use regular foam to remove stains from polyurethane foam. "demixide", that is, a remedy for joints. To remove the stain, you will therefore need to protect your hands with rubber gloves. Apply the product and leave for 15 – 20 minutes. During this short period of time, the foam structure will have time to soften, which will allow you to quickly remove it with a sponge. After this, the product requires washing.
If, after much effort and waste of energy, you are unable to get rid of the unpleasant stain, you can turn to dry cleaning for help. They probably know effective methods for removing such stains.
You must always remember that when removing stains from polyurethane foam using aggressive agents, you need to use personal protective equipment, that is, gloves and a respirator. Also, if you are not sure about the safety of the fabric product, it is better to do a small test on the inside.
conclusions
During the repair process, it is necessary to avoid in every possible way unpleasant contamination with polyurethane foam, which is very deeply absorbed into the fabric and difficult to remove. To do this, it is recommended to wear work clothes that have lost their appearance. In the event that it was not possible to avoid contamination, it is worthwhile to begin removing stains as quickly as possible, since there is not much time to waste.
