Knowing the fault codes of the Indesit washing machine often quickly solves the problem of self-diagnosis and eliminating the problem.
The malfunction is displayed on the liquid crystal display of the device, which determines the error code. A flashing LED indicator will indicate the type of breakdown and make it clear what is the best course of action - make the simplest repair yourself, or call a professional from the service center.
It is always useful to have a reminder with a classification of machine trouble codes and methods for eliminating them.
Error codes are formed from the Latin letter F and a number.
Error Codes and Troubleshooting Methods
F01 - short circuit of the electric motor.
The solution to the problem is to choose one of the following actions.
Need to check:
- Electric motor and electrical circuits;
- Avoiding getting the connector contacts wet;
- Electric motor for absence of corrosion on metal contacts.
It is possible to install a new engine or repair it.
F02 — no signals are received from the tachogenerator. The drive motor is not working properly. Need to review:
- Electric motor;
- Controller connecting contacts;
- Check the generator resistance.
The action consists of changing the electronic module or electric motor. Or we change the tachogenerator.
F03 - The temperature sensor is broken, the heating element relay is stuck. The controller turns on the heating, but the water does not heat up. We check:
- Electrical resistance - the reference value is 20 kOhm at t +20 degrees;
- Heating element relay, electrical networks;
- Electronic controller.
We are looking for a solution in changing the temperature sensor, repairing the electrical network, or changing the module itself.
F04 — malfunction of the pressure switch - water level sensor in the tank. At the same time there are two signals “Overflow” and “Overflow”. The drain turns on and the water fill valve opens. We work on inspection:
- Pressostat, controller and connecting circuits.
Upon completion of the audit, you need to reinstall the pressure switch or controller.
F05 – the drain pump does not function; after draining there is no “Empty tank” signal.
Need to check:
- Serviceability of the controller, connecting circuits;
- pump;
- Drain hose.
The action consists of cleaning the filter and replacing the pump.
F06 — failure of the washing program selection buttons on the control panel.
We carry out an audit:
- The controller and its connections to the control panel;
- Electronic control module.
The control panel or module may need to be reinstalled.
F07 - there is a signal “Empty tank”, insufficient water level. Connecting the heating element is prohibited, since there is no water flow. To prevent heating equipment from burning out, protection is activated.
Need to check:
- Thermal relay of the heating element, pressure switch, electrical circuits;
- Compliance with the standard water pressure in the water supply;
- Water level switch.
Based on the test results, install a new sensor or module.
F08 — there is a message that the heating element is not working, the relay contacts are stuck.Two signals are given simultaneously - “Overflow” and “Tank is empty”. It is necessary to check:
- wiring connecting the relay with the sensor, heating element with electrical equipment;
- heating element, controller.
After the inspection, install a new level sensor or controller.
F09 - indicates a failure in the memory of the electronic control unit; the sensor does not operate.
- Check the voltage in electrical networks;
- We reboot the device by disconnecting it from the network for 20 minutes.
To eliminate this error, you need to reinstall the program or a new microcircuit.
F10 – reports violations in the operation of the water level sensor. There is no signal about the status of the working tank. Therefore the heating cycle does not start. This is often associated with error code F04.
- We check the pressure switch and electrical networks.
Perhaps one of the nodes requires replacement.
F11 – there is no message about the operation of the pump. This indicates a problem with the electrical circuit or wear on the pump winding.
We conduct an audit:
- Drain pump-module connections;
- Pump winding integrity;
- Filter for clogging.
If the error is not corrected, you need to change the pump or electrical module. In 99% of cases, the signal factor is pump failure.
F12- this error code indicates a breakdown in communication between the control module and indicators. Necessary:
- Disconnect the device from the network for 20 minutes to reboot;
- Check the contacts between the controller and the bulbs.
The repair will consist of re-equipment of the module, buttons and indicators, as well as revision of contacts and electrical wiring.
F13 – the dryer temperature sensor does not function. After the wash cycle, the laundry drying function does not turn on. Proceed as follows:
- Turn off the machine to reboot;
- Check the wiring and connections between the machine and the sensor.
If necessary, change the temperature sensor of the device.
F14.15 – the heating element of the washing machine does not work. The laundry drying function does not turn on.
- We reboot the device by disconnecting it from the network for half an hour;
- Check the connection board.
We repair the wiring and replace the heating element.
F16,17— problems with blocking:
F16 - drum blocking error in machines with vertical loading;
F17 — The hatch door lock does not close or is not closed tightly. Blocking protection prevents the unit from starting.
The actions are:
- checking the reliability of the lock or replacing it;
- installation of a new electronic module.
F18 – the electronics module has become unusable. Change or repair the “brain” of the device.
Tips for repairing Indesit washing machines
The Indesit brand is the youngest among the popular ones. It is represented by an extensive model range. Often these are budget modifications of cars, good in terms of price-quality ratio. In addition, the advantage is their high suitability for repair work. Almost all spare parts for repairs are available in workshops and their cost is quite low.
The most common failures of the Indesit washing machine are the locking lock, the drum and the electronic “brain” of the control system.
Self-diagnosing machine malfunctions is an extremely difficult task. It can be difficult for the average consumer to understand the design features of the device.
It is better to entrust repairs to a washing machine that is under warranty to a qualified specialist.
If the device is covered by a warranty, you do not need to open it yourself. In this case, all breakdowns must be carried out free of charge by the relevant repair shop.
A malfunction is considered serious if smoke appears during operation of the mechanism.
Only a qualified technician can conduct a complete examination of the entire system, and this is done only with special equipment.
Error codes reflect only the consequence of a breakdown, and not its cause. But their knowledge guides the search direction and saves time. True, you will need knowledge of the equipment design and the principles of interaction of individual nodes. Modern consumer electronics are becoming more complex, functional and, as a result, less reliable.
In addition, it is important to correctly assess the faults before deciding to repair or replace parts.
