Electrolux washing machine error is a set of symbols that are displayed on a small display on the main panel of the machine. If any malfunctions occur during the washing process, this display will definitely show what kind of problem occurred. However, this will not be written in normal and understandable text, but will only display a code showing you exactly what has happened and what needs to be repaired or adjusted. The article will help you if some kind of malfunction has occurred with your machine, and you do not know what kind of obscure set of characters appeared on the screen.
Let's start with the fault code E11. If you notice that these 3 symbols appear on the display, it means that the process of pouring water into the tank during the washing process is disrupted. This problem may arise due to a simple blockage in the hose through which water flows. However, this often happens due to a malfunction of one or more valves through which water is poured.
Error E13: This error indicates that water has leaked into the pan of your machine. Check if this is the case and, if so, drain the water from the pan.
Malfunction E21. E21 indicates that within 10 minutes the water that should have been drained did not pour out of the tank. Most likely the problem is in the pump. However, this could be due to a clog in the pipes or drain hose.
E23 – problems with the drain control (triac). Check and, if there is a problem, replace this part.
Code E24: There is a malfunction with the drain system triac control circuit. Corrected after checking the specified circuit.
E31: pressure sensor failure. It is necessary to check and, if necessary, correct the wiring, or replace the above sensor.
E32: Problem with pressure sensor calibration. In this case, you need to take some actions: open the tap, replace the water inlet valve, clean the existing filters, replace the pressure switch tube, change the pressure sensor.
E33: Sensors indicating the water level do not work consistently. Most likely, the problem is in one of these sensors and this can be solved by identifying which sensor is at fault and replacing it.
E34: problem of compliance of the pressure switch and the anti-boiling level 2. It is necessary to replace the pressure sensor and, if necessary, the pressure switch tubes.
E35: too much water in the washing machine. You need to check the water level sensor and, if it is faulty, replace it.
E36: malfunction of the sensor indicating the temperature level of the heating element. The sensor needs to be replaced.
E37: Level 1 water sensor failure. It is necessary to check this element for faults and, if necessary, replace it with a new one.
E38: there is no signal about a change in water pressure. The problem is most likely in the tube through which the water flows. It needs to be cleaned and the problem will disappear.
E39: breakdown of the water overflow pressure switch. This element needs to be checked or replaced.
E3A: This error indicates that there is a malfunction in the heating element relay. The only solution is to replace this relay.
E41: we can say that it is the most harmless mistake.This code is displayed if the washing machine hatch is not closed or is not closed tightly. To resolve the problem, open and close the door again.
E42: malfunction of the lock responsible for tightly closing the hatch. Check that the closing mechanism is functioning properly and, if necessary, replace the mechanism.
E43: breakdown of the hatch blocking control triac. This problem can be solved by diagnostics and, most likely, by replacing the triac.
E44: You know that when the machine finishes the washing process, the door automatically opens. If this does not happen, then the display will display error E44, which tells you that the sensor responsible for receiving the signal about the end of the working cycle has failed and the door did not open. This sensor needs to be replaced.
E45: breakdown in the hatch lock control circuits. It is necessary to check the entire lock control circuit and identify the malfunction, and then eliminate it.
E51: The control triac of the electric motor has closed. It is necessary to diagnose this element and, if a problem is identified, solve it.
E52: no signal is received from the electric drive tachometer. Basically, error E52 is displayed if the fastening of the tachometer to the housing is broken. You need to check the latch (washer) and find out if it was in place.
E53: a breakdown in any part of the motor control circuit. Check the entire control circuit for faults, replace failed elements with new ones.
E54: failure of one of the 2 groups of contacts in the motor relay. Only replacing the failed contact group will help.
E55: violation of the integrity of the electric motor circuit.It is necessary to check the wiring and drive circuit, replace elements in which violations are detected.
E56: There is no signal coming from the tachometer on the generator. The tachometer needs to be replaced or the wiring checked. Most likely, the problem is in the former, but wiring can often cause error E56.
E57: voltage exceeds the maximum permissible (15A). The most common problem that causes this error is a wiring problem. It is advised to replace it entirely, or carry out diagnostics and identify in which areas there are violations.
E58: the current flowing in the electric motor exceeded 4.5A. You need to check the parts and find out where the fault is. The error will disappear if you replace one of the elements: engine, wiring, electronic module.
E59: problem with the electric motor, faulty electronics. It is necessary to check and, if necessary, replace the wiring.
E5A..E: The electronic unit is faulty, it needs to be replaced
E61 and 62: The heating elements fail, causing the water to heat up longer than expected
E66: The heating element is faulty or there is a problem in the entire system that heats the water. It is necessary to diagnose the wiring, as well as the relay, which is responsible for the heating element and its operation.
E71: the thermistor has failed. Most often, this happens when the sensor of this device fails. Replace it.
E74: The sensor indicating the temperature is not positioned correctly. You need to return it to its original position.
E82..84: Malfunction in the electronic module. It is necessary to diagnose it and troubleshoot it.
E85: a serious error indicating that the main pump or pump has failed.
E91: lack of communication with the host computer most often occurs as a result of wiring problems. It is necessary to diagnose the wires.
Error group E92-E99 will indicate to you problems with the electronic unit. If the screen shows such values, then run diagnostics on this module.
EA1..EA6: All errors in this category indicate a DSP malfunction. In any case, diagnostics are necessary, with possible replacement of the electronic module or wiring.
EB1..EB3: problems with the voltage supply. The problem may occur due to faults in the wiring or the unit supplying voltage.
EF1: the water drainage time does not correspond to the regulated one. This problem can arise if there are problems with the pump.
EF2: a lot of foam. If you use unsuitable detergents, foaming may increase significantly. In this case, this error will appear on the screen. Read more carefully which laundry detergents are most wise to use in your washing machine.
EF3: There is a problem with the wiring connected to the pump. Diagnose the wires and fix the fault if found.
EF4: the sensor responsible for indicating water flow does not produce a signal. Most likely, the water pressure is insufficient.
EF5: spinning is stopped. This means that the loading of the machine has exceeded the norm specified in the technical passport.
EN1: The power board is not functioning properly.
EN3: The input voltage is below normal. The electronic module needs to be replaced.
ENE: the electronic unit needs to be replaced, because... The safety circuit relay has failed.
EHF: The protective circuit does not pass the identification process. Most likely, the electronic module will need to be replaced.
